dzisiaj 08:35
[#31]
Re: Driver USB (XHCI) dla Pistorm/RPi4B
@Kitech, post #30
# Sample config.txt file for booting Emu68 with Pistorm
kernel=Emu68-pistorm.gz
disable_splash=1
arm_64bit=1
# Default boot delay is one second. Uncomment this line if you want zero second delay
boot_delay=0
# This is important so that GPU firmware does not add its overlay icons on the screen
# If you also want to disable speed throttling in case of undervoltage, set this value to 2
avoid_warnings=2
# Enable the options below to increase speed of ARM cpu to 1.5GHz
# Keep in mind this may render your RasPi3 unstable and eventually void the warranty!
force_turbo=1
over_voltage=4
arm_freq=1800
# CM4 users may use dtparam=ant2 to select external antenna. Otherwise
# internal antenna is selected (equals to: dtparam=ant1)
dtparam=ant2
# Force HDMI signal even if nothing is connected
hdmi_force_hotplug=1
# Force 1080p video mode. Comment out the hdmi_mode line if your monitor
# does not like it. For list of all modes please refer to RasPi documentation
# https://www.raspberrypi.com/documentation/computers/config_txt.html#hdmi-mode
hdmi_group=2
hdmi_mode=82
# Experimental 2560x1440 50Hz mode for RaspberryPi which you can give a try. If you do,
# comment the hdmi_mode above
#hdmi_group=2
#hdmi_mode=87
#hdmi_cvt=2560 1440 50 3 0 0 1
#max_framebuffer_width=2560
#max_framebuffer_height=1440
#hdmi_pixel_freq_limit=400000000
# The ROM is selected through initramfs parameter. As a file name give the full name of your
# kickstart file which you have placed on the RasPi boot partition. If there is a development version
# of FPGA firmware to load (PS32Lite) or to upgrade (all others, not yet implemented), it must be
# gzip-compressed and passed **before** the ROM name, separated from the rom with a comma.
# NOTE: The default firmware for PS32Lite is already embedded in Emu68!!! Above instruction is
# for test/development purposes **ONLY**
#initramfs firmware.bin.gz,DiagROM
initramfs A1200.47.115.rom
kernel=Emu68-pistorm.gz
disable_splash=1
arm_64bit=1
# Default boot delay is one second. Uncomment this line if you want zero second delay
boot_delay=0
# This is important so that GPU firmware does not add its overlay icons on the screen
# If you also want to disable speed throttling in case of undervoltage, set this value to 2
avoid_warnings=2
# Enable the options below to increase speed of ARM cpu to 1.5GHz
# Keep in mind this may render your RasPi3 unstable and eventually void the warranty!
force_turbo=1
over_voltage=4
arm_freq=1800
# CM4 users may use dtparam=ant2 to select external antenna. Otherwise
# internal antenna is selected (equals to: dtparam=ant1)
dtparam=ant2
# Force HDMI signal even if nothing is connected
hdmi_force_hotplug=1
# Force 1080p video mode. Comment out the hdmi_mode line if your monitor
# does not like it. For list of all modes please refer to RasPi documentation
# https://www.raspberrypi.com/documentation/computers/config_txt.html#hdmi-mode
hdmi_group=2
hdmi_mode=82
# Experimental 2560x1440 50Hz mode for RaspberryPi which you can give a try. If you do,
# comment the hdmi_mode above
#hdmi_group=2
#hdmi_mode=87
#hdmi_cvt=2560 1440 50 3 0 0 1
#max_framebuffer_width=2560
#max_framebuffer_height=1440
#hdmi_pixel_freq_limit=400000000
# The ROM is selected through initramfs parameter. As a file name give the full name of your
# kickstart file which you have placed on the RasPi boot partition. If there is a development version
# of FPGA firmware to load (PS32Lite) or to upgrade (all others, not yet implemented), it must be
# gzip-compressed and passed **before** the ROM name, separated from the rom with a comma.
# NOTE: The default firmware for PS32Lite is already embedded in Emu68!!! Above instruction is
# for test/development purposes **ONLY**
#initramfs firmware.bin.gz,DiagROM
initramfs A1200.47.115.rom
